To in instrumentation and control engineering is

To acquire education in the field of
electronics systems and gain an edge over my counterparts, I want to study M.Eng Electronic Systems Engineering at the
University of Regina. With the help of this application, I would like to present
my candidature in front of the admission committee of the University.

My decision to major in instrumentation and
control engineering is a direct result of my desire to contribute to the
development of industrial systems in my country. After my matriculation and
senior secondary, I took admission in Bachelor of Engineering in
Instrumentation and Control in 2013.

We Will Write a Custom Essay Specifically
For You For Only $13.90/page!


order now

During my undergraduate degree in
Instrumentation and Control Engineering at Sardar Vallabhbhai Patel Institute
of Technology, besides expanding the range of my knowledge, the course
curriculum has given me valuable insight into practical aspects of the study. I
also got the knowledge of fundamentals of instrumentation and control
especially in the field Control System Design, Power Electronics, Electronic
Devices and Circuit, Digital Logic Circuit, Industrial Measurement, Circuits
& Network, Analog signal processing and Biomedical instrumentation. I am
fully familiarized with all these subjects. I am familiar with programming
languages like MATLAB & Simulink, LABVIEW & Siemens’ software for PLC
(Programmable Logic Controller), SCADA & Control Builder F for Distributed
Control System as well as the new upcoming Prosthetic concept in the biomedical
field.

As a part of course curriculum, I have worked
on various projects related to my subjects. As one of my project in the second
year, I used 8051 Microcontroller for interfacing DC motor both clockwise and
counterclockwise directions. My design engineering project was based on solar
sensors. It was focused to increase the efficiency of solar panels using
Maximum Power Point Tracking Theory. My third-year project was on PLC based in
which forward and reverse 3 phase motor control had been done using PLC. My
final year project is on ‘Controlling of Wireless Gesture Controlled Robotic
Arm’. In this project, we have used Atmega-16 microcontroller, wireless radio
frequency module, servo motors, power-supply circuit and mechanical assembly of
an arm. In this project, we match the data on the receiver side and the
transmitted data from the operating side via a radio frequency module
supporting a range of up to 100 meters.

Apart from academics activities in school
& college, I was also actively participated in outdoor activities. I got
3rd rank in project presentation in the 7th semester of my degree. I also got
1st rank in seminar presentation in my class. I have also served as an event
volunteer in the national level technical symposium ‘PRAKARSH’ and in VISION
(Intra college technical symposium) consistently from the second year till the
last year organized at my college. In my second year, I was the event
coordinator in the event called ‘Robotics’. In the third year, I was the Event
head of the same event. In the final year, I was one of the members of the
advisory committee of the ‘Robotics’ event. Meanwhile, I completed my bachelor degree with 7.76 CGPA in 2017.

I often read the leading journals about power
and digital systems. This Electronic System Engineering covers almost every
subfield such as, Bio-medical Instruments, Digital Electronics, and Signal
Processing which are same as my undergraduate subjects which develops an
interest in me to take up my career for M.Eng in “Electronic System Engineering”.
My coursework on related subjects, at the undergraduate level, had just
enhanced my keen for this subject and thereby I have decided to pursue my M.Eng
Electronic System Engineering. My other areas of interest are Control System,
Programmable Logic Controller, Distributed Control System, Biomedical Instruments,
and Automation.

Thus, armed with the much-valued consent and
guidance from my HOD and professors, discussion with my seniors and careful
study of the web pages of your University, I am convinced that my academic
career will receive the much-required magnification enabling me to pursue
considerable research and excel at it. I have gone through the university
publications and website very carefully and I concluded that with we have
similarity in the field of interest, so University of Regina will provide a perfect
environment to focus all my resources towards M.Eng program. Not only high
reputation attracts me, but also does the subjects and the on-going researches
by renowned faculties. I want to enhance my skills in this field under your
tutelage.

My undergraduate curriculum has enabled me to
clear my basic fundamentals, and now I want to increase the attained knowledge
through a Master’s course at the University of Regina at CANADA. The main
reason for which I have taken the decision to pursue graduate studies in CANADA
is the fast emerging global scenario in this Electronic System Engineering
field and also the quality of the education. I think pursuing this degree from
CANADA will help me in the industry and bring me back to my country where I can
work for better automation and instrumentation facilities to improve the
infrastructure and communication.

As a student, my experience says that good
facilities can make a difference in a student’s life and learn exposure. I
believe that I have the ability and determination to trend on this exciting
path of graduation.

I hope that I will be given a fair chance to
pursue my Master’s Degree at your leading University. I look forward to a long
and fruitful association with the University of Regina.